Stokta Yok
Elnec

Top PSOP44 ZIF 600mil + Bottom PSOP44 NOR-1 Soket Seti

Elnec
Fiyat
:
175,00 USD + KDV
KDV Dahil
:
206,50 USD
Paylaş:
Ürünle İlgili Öne Çıkan Kampanyalar

{{CMP.TITLE}}

{{CMP.DESCRIPTION}}

  • Ürün Özellikleri
  • Ödeme Seçenekleri
  • Yorumlar (0)
  • Tavsiye Et
  • Resimler
  • Top PSOP44 ZIF 600mil + Bottom PSOP44 NOR-1 Adaptör Soket Seti

     

    ·         bottom board of PSOP44 adapters, assigned for Flash devices with pinout NOR-1

    ·         made in Slovakia

    Ord. no.

    70-1231

    Socket

    2x24 sockets for wire wrap pin

    Bottom

    2x24 pins, square, 0.6x0.6mm, rows spacing 600mil

    Class

    Specialized

    Subclass

    Memory (NOR/NAND/eMMC)

     



    ·         top board of PSOP44 adapters (mainly FLASH EPROM with 44-pins)

    ·         operating (mechanical) warranty of ZIF socket - 10,000 actuations

    ·         made in Slovakia

    Ord. no.

    70-1232

    Socket

    ZIF PSOP44, OpenTop type

    Bottom

    2x24 pins, square, 0.6x0.6mm

    Class

    Specialized

    Subclass

    Memory (NOR/NAND/eMMC)

     

     

     

     

     

     

     

     

     

     





    Adapter manual (Top)

    • For work with PSOP44 device it is necessary put together Top PSOP44 ZIF 600mil with some Bottom PSOP44-x board according to the information provided by PG4UW software.
    • The picture show, how to put together the Top PSOP44 ZIF 600mil and Bottom PSOP44-x boards to have complete PSOP44 adapter.
    • Insert comlete adapter to the device programmer ZIF socket according to the picture placed near of it. If you have some doubts about orientation of this adapter in device programmer ZIF socket, it is valid general rule, the orientation of the text of title is the same as the text on the top of the device programmer.
    • Push the top of adapter ZIF socket to open it. Insert the device into the adapter ZIF socket. The right position of the programmed device in adapter ZIF socket is show at picture near (mainly left above) the adapter ZIF socket. Then release adapter ZIF socket.
    • Visually check interconnection between device and adapter ZIF socket. If everything looks OK, the device is ready for programming.
    • Be careful, because the incorrect insertion of adapter to the device programmer ZIF socket or device to the adapter ZIF socket can damage the programmed device.
    • To take out the device push the top of adapter ZIF socket and remove device from it.
    • When you finish work with adapter, remove it from the device programmer ZIF socket.
    • Do not directly touch the pins of the adapter and adapter ZIF socket, because dirt may cause errors during programming of device.
    • For handling with the device we recommended to use a vacuum pick up tool.
    • Operation conditions: operating temperature 5°C ÷ 40°C (41°F ÷ 104°F), operating humidity 20%..80%, non condensing.

     

     

    Adapter manual (Bottom)

    • For work with PSOP44 device it is necessary put together Bottom PSOP44 NOR-1 with Top PSOP44 ZIF 600mil board according the information provided by PG4UW software.
    • The picture show, how to put together the Top PSOP44 ZIF 600mil and Bottom PSOP44-x boards to have complete PSOP44 adapter.
    • Insert comlete adapter to the device programmer ZIF socket according to the picture placed near of it. If you have some doubts about orientation of this adapter in device programmer ZIF socket, it is valid general rule, the orientation of the text of title is the same as the text on the top of the device programmer.
    • Push the top of adapter ZIF socket to open it. Insert the device into the adapter ZIF socket. The right position of the programmed device in adapter ZIF socket is show at picture near (mainly left above) the adapter ZIF socket. Then release adapter ZIF socket.
    • Visually check interconnection between device and adapter ZIF socket. If everything looks OK, the device is ready for programming.
    • Be careful, because the incorrect insertion of adapter to the device programmer ZIF socket or device to the adapter ZIF socket can damage the programmed device.
    • To take out the device push the top of adapter ZIF socket and remove device from it.
    • When you finish work with adapter, remove it from the device programmer ZIF socket.
    • Do not directly touch the pins of the adapter and adapter ZIF socket, because dirt may cause errors during programming of device.
    • For handling with the device we recommended to use a vacuum pick up tool.
    • Operation conditions: operating temperature 5°C ÷ 40°C (41°F ÷ 104°F), operating humidity 20%..80%, non condensing.
T-Soft E-Ticaret Sistemleriyle Hazırlanmıştır.